How to Use a Pool Vacuum

How Does a Pool Vacuum Cleaner Work

The six settings of a sand filter

Most of these sand filters come with a six-port valve which has various settings. So let’s identify what each of these settings does.

  1. Pool filter- it is the duty of the sand filter, it purifies ninety-nine percent of the water in the swimming pool.
  2. Waste- the water passes throughout the sand filter directly, avoiding the sand. It is usually when the pool gets a lot of dirty, and it needs a deep pool cleaning. You need to remember that this setting would empty your swimming pool.
  3. Backwash- it is a small sand cleaning cycle to improve the purification. Just check the maintenance of the pool filter. Usually, you need to do this at least once per week. The pool water gets wash back along the sand in a reverse way, by removing the waste from the pool filter material.
  4. Rinse- it is the setting you need to use right after you do the backwashing. Let the water pass through the sand filter from the top to end for about thirty seconds, so the water gets drawn into the system of the sewer. It would make sure that all the sand is back in the right place and the remaining waste is drained out.
  5. Circulation- the water goes straight back to the pool from the pool pump without going along the filter. Eventually, this means the water is not fresh.
  6. Closed- every port is closed. In case, if the pool pump is still switched on, ensure that you turn it off within few seconds, or as a result, the pressure increases fast. Usually, you use this setting when you service the pool pump. By this way, water will not get back to the pool pump from the filter when you turn the pump off for a while

Maintenance of the pool filter of the swimming pool

You need to maintain your swimming pool filter regularly. Usually, it only requires a little bit of support. You need to purify your filter by doing a backwash once a week for around five minutes. After that, you need to set the pool filter to “rinse” so that it can wash away any remaining waste quickly.

After the five years, you would have to replace the sand in your pool filter. At that time, the upper layer of sand would be harder to penetrate due to collected matter. So the filter might get clogged, raising the pressure within the filter and minimising the flow rate of the filter. By not replacing sand to your pool filter, you might end up breaking it down entirely.

So, here is our step by step guide on vacuuming the pool to waste. All you need is a vacuum head, a vacuum hose and a pool vacuum extension pole. Follow our step by step guide to vacuum your pool to waste.

Step 01

The first thing you must do to start up with the vacuuming is to raise the water level of your swimming pool. You can increase the water level by using a garden hose. Make sure that you position it in a way that it won’t stir the debris and the dirt in the pool.

Step 02

Then next, you have to turn off the circulation pump of the pool so that the water in the pool will remain still, making it easier for you to clean the pool.

Step 03

Attach the pole to the end of the swivel of the vacuum hose. Vacuuming to waste would consume a lot of suction so make sure that everything is in the right place. Don’t forget to turn off the pool heaters or pool cleaners before you start with vacuuming.

Step 04

Then you must set the filter to the waste feature since most filters come with this feature so you can vacuum your pool to waste. Watch it when the pump is on.

Step 05

Make sure that you won’t break the suction by pulling the plate loosely. You will have to turn off the pump and clean the debris in the hair and lint pot.

Step 06

What if your vacuum doesn’t allow you to set it to waste? Then here is what you should do.  Attach the extension pole at the end of the vacuum head and then the end of the hose to the pole’s end. Now, since everything is set, all you have to do is to dip the vacuum head deep inside the swimming pool and start cleaning right away.

Step 07

Next, you must keep holding to the pole to stabilize the vacuum head when it sinks. Then, submerge the hose into the pool so that it descends and get filled with water.

Step 08

Then, to activate the suction, you must connect the vacuum hose to the skimmer port. Then start vacuuming back and forth by holding from the extension pole.

Step 09

Once you see that the water level is going down below the skimmer, you must stop vacuuming, and the circulation pump must be turned off. Unplug the vacuum hose from the skimmer port and remove it away from the pool.

Step 10

This is the final step, and now your swimming pool is clean as new. Turn on the settings back to the filter setting again and switch on the pump. Your pool is all ready for the normal functioning now.

Hope that our step by step guide on vacuuming the pool to waste was useful for you. Get your pool freed from large debris, dirt and algae so that you can keep enjoying in a clean swimming pool once again.

By | 2018-05-31T21:38:21+00:00 May 12th, 2018|Categories: pool filter, tips|0 Comments

About the Author:

HI Thanks for visiting my blog, I’m Danielle Fudge, Over 13 experience in Swimming Pool Cleaning, Maintenance, and Inspection in Hillsville, Virginia area. In 2012, I decided to put my experience & bargain hunting skills to good use and start this blog poolclincs.com. My main goal is to help you look for information and find the best product which suits your requirement. If you have any concern please don’t hesitate to send me an email. poolclinicsreviews[at]gmail.com